Railway coupling

For other uses, see Coupling (disambiguation).

Scharfenberg coupler on a Southeastern Class 395

Video of ICE T coupling at Leipzig Hauptbahnhof

A coupling or coupler is a mechanism, typically located at each end of a rail vehicle, that connects them together to form a train. The equipment that connects the couplers to the vehicles is the draft gear or draw gear, which must absorb the stresses of the coupling and the acceleration of the train.

Throughout the history of railroading, a variety of coupler designs and types have been developed worldwide. Key design considerations include strength, reliability, easy and efficient handling, and operator safety. Automatic couplers engage automatically when the cars are pushed together. Modern versions not only provide a mechanical connection, but can also couple brake lines and data lines.

Different countries use different types of couplers. While North American railroads and China use Janney couplers, railroads in the former Soviet Union use SA3 couplers and the European countries use Scharfenberg and screw couplers. Challenges and complications arise when coupling vehicles with different couplers. Barrier cars, also called match cars, cars with dual couplers, or adapters are used to accomplish this task.

Nomenclature

Compatible and similar couplings or couplers are frequently referred to using widely differing make, brand, or regional names, or nicknames, which can make describing standard or typical designs confusing. Dimensions and ratings noted in these articles are usually of nominal or typical components and systems, though standards and practices also vary widely with railway, region, and era.

Buff: when the consist (one or more cars coupled together) of cars is in compression; opposite of tension.

Buffers and chain

Main article: Buffers and chain coupler

The basic type of coupling on railways following the British tradition is the buffer and chain coupling. A large chain of three links connects hooks on the adjoining wagons. These couplings followed earlier tramway practice but were made more regular. Buffers on the frame of the wagon absorbed impact loads, as the train overran a slowing locomotive.

The simple chain could not be tensioned, and this loose coupling allowed a great deal of back and forth movement and bumping between cars, as well as jarring when trains started. While acceptable for mineral cars, this coupling made for an uncomfortable ride in passenger coaches, so the chain was improved by replacing the center link with a screw with a left-hand thread on one side and a right-hand thread on the other. In the center of the screw is the handle housing with a hinged ball handle attached. This turnbuckle style arrangement allows the vehicles to be pulled together by tightening the screw with the attached handle. Typically, the screw is tightened until there are two threads left next to the handle housing. A support is attached to the trunnion nut on the coupling link side to rest the handle of the screw to prevent loosening of the screw while the coupling is in use. The official name of this type of coupling is screw coupling or UIC coupling according to the European standard EN 15566 Draw gear and screw coupling.

A simplified version of this, quicker to attach and detach, still used three links but with the centre link given a T-shaped slot. This could be turned lengthwise to lengthen it, allowing coupling, then turned vertically to the shorter slot position, holding the wagons more tightly together.

Higher speeds associated with fully-fitted freight made the screw-tensioned form a necessity.

The earliest 'dumb buffers' were fixed extensions of the wooden wagon frames, but later spring buffers were introduced. The first of these were stiff cushions of leather-covered horsehair, later steel springs and then hydraulic damping.

This coupling is still widespread in Western and Central Europe and in parts of Northern Africa, the Middle East and South Asia.

• 
  Three-link coupling on an antique tank wagon
• 
  UIC standard screw coupling, shown attached and tightened

Link and pin

A link-and-pin coupler

Transition era AAR knuckle coupler. The gap in the knuckle accommodates the link of a link and pin coupler and the vertical hole in the knuckle accommodates the pin.

Link and pin coupler combined with side buffers on a Panama canal mule.

The link-and-pin coupling was the original style of coupling used on North American railways. After most railroads converted to semi-automatic Janney couplers, the link-and-pin survived on forest railways. While simple in principle, the system suffered from a lack of standardisation regarding size and height of the links, and the size and height of the pockets.

The link-and-pin coupler consisted of a tube-like body that received an oblong link. During coupling, a rail worker had to stand between the cars as they came together and guide the link into the coupler pocket. Once the cars were joined, the employee inserted a pin into a hole a few inches from the end of the tube to hold the link in place. This procedure was exceptionally dangerous and many brakemen lost fingers or entire hands when they did not get them out of the way of the coupler pockets in time. Many more were killed as a result of being crushed between cars or dragged under cars that were coupled too quickly. Brakemen were issued with heavy clubs that could be used to hold the link in position, but many brakemen would not use the club, and risked injury.

The link-and-pin coupler proved unsatisfactory because:

• It made a loose connection between the cars, with too much slack action.
• There was no standard design, and train crews often spent hours trying to match pins and links while coupling cars.
• Crew members had to go between moving cars during coupling, and were frequently injured and sometimes killed.
• The links and pins were often pilfered due to their value as scrap metal, resulting in substantial replacement costs.
• When a car happened to be turned 180 degrees one would have to look for a link.
• Railroads progressively began to operate trains that were heavier than the link-and-pin system could cope with.

In Britain link-and-pin couplers were common on narrow gauge industrial and military railways, and eventually evolved into a form that could be reliably coupled when the train was stationary.

The Panama Canal mules, the locomotives used to guide the ships through the locks of the Panama Canal, have link and pin couplers and side buffers. This design was chosen so that these normally solo operating locomotives could be coupled to another locomotive in the event of a breakdown. On straight track, the link and pin coupler is used. Since the vertical curve between the straight track sections and the ramp between the lock chambers has a very small radius, the difference in height would be too great for a link and pin coupler, so the locomotives must be pushed through these sections uncoupled by using the side buffers. They have an extra high buffer plate to prevent the buffers from buffer-locking in tight vertical curves.

Balance lever coupling

Main article: Balance lever coupling

Balance lever coupling on narrow gauge coach in Switzerland

The balance lever coupling, also central buffer coupling with two screw coupling, is a coupler commonly used on narrow gauge railroads with tight curves. By swapping the pulling and pushing devices, the standard screw coupling used on standard gauge railroads became a center buffer coupling with one screw coupling on each side of the buffer. The screw couplers are connected to a compensating lever that pivots on a vertical trunnion on the center buffer rod, allowing an even distribution of tractive forces between the two screw couplers.

Albert coupler

Albert coupler on a European tram

To avoid safety issues, Karl Albert, then director at the Krefeld Tramway, developed the Albert coupler during 1921. The Albert coupler was created as a key and slot coupler with two pins. Vehicles to be coupled were pushed together, both couplings moving to the same side. One pin was inserted, then the vehicles were pulled to straighten the coupling and the other pin inserted. This operation required less exact shunting. Due to the single-piece design, only minimal slack was possible. The system became quite popular with tram systems and narrow gauge lines.

During the 1960s most cities replaced them with automatic couplers. But even in modern vehicles, Albert couplers get installed as emergency couplers for towing a faulty vehicle.

Miller hook and platform

The link and pin was replaced in North American passenger car usage during the latter part of the 19th century by the assemblage known as the Miller platform, which included a new coupler called the Miller hook. The Miller platform (and hook coupler) was used for several decades before being replaced by the Janney coupler.

Norwegian

Main article: Norwegian coupling

Norwegian coupling in Uganda

The Norwegian coupler consists of a central buffer with a movable hook that drops into a slot in the central buffer. There may also be a U-shaped safety catch on the opposite buffer that is flipped over the top of the hook to secure it. The safety device may also be a chain with a ball-shaped weight at the end that is thrown over the hook to hold it in place. On railways where the rolling stock always face the same direction, the mechanical hook can be on one end of the wagon only. Not all Norwegian couplers are compatible with one another as they vary in height and width, and may or may not be limited to one hook at a time. The traction force limit is typically 350 kN. Sometimes the Norwegian coupler is supplemented with auxiliary chains.

The Norwegian coupler is also known as the Lloyd coupler named after its British manufacturer F.H. Lloyd & Co. Ltd near Wednesbury or as the meat chopper coupler named after the shape of the movable hook. The Norwegian coupler allows sharper curves than the buffer and chain coupler, which is an advantage on narrow gauge railways where low speeds and reduced train loads allow a simpler system. The Norwegian coupler is found only on narrow gauge railways of 1,067 mm (3 ft 6 in), 1,000 mm (3 ft 3+3⁄8 in) or less in Great Britain and its former colonies. For example, it is used on the Isle of Man Railway, the Western Australian Government Railways, in Tanzania, on the Ffestiniog Railway, on the Lynton and Barnstaple Railway, and on the Welsh Highland Railway,

Radial couplers

Two versions of radial coupler were used in South Africa. One, the Johnston coupler, commonly known as a bell link-and-pin coupler, was introduced in 1873 and is similar in operation to and compatible with link-and-pin couplers, but bell-shaped with a circular coupler face. The other, the bell-and-hook coupler, was introduced in 1902 and is similar to the Norwegian coupler, but also with a circular coupler face and with a coupler pocket which is open at the top of the coupler face to accommodate the drawhook.

Johnston coupler

Transition era AAR knuckle coupler. The gap in the knuckle accommodates the link of a Johnston coupler and the vertical hole in the knuckle accommodates the pin.

The Johnston coupler, commonly known as a bell link-and-pin coupler from its bell shape, was first introduced in the Cape of Good Hope in 1873, following the establishment of the Cape Government Railways (CGR) in 1872 and the decision by the Cape government to expand the railways into the interior and to convert the existing tracks from 4 ft 8+1⁄2 in (1,435 mm) standard gauge to 3 ft 6 in (1,067 mm) Cape gauge. All new Cape gauge locomotives and rolling stock acquired from 1873 were equipped with these or similar couplers, beginning with the CGR 0-4-0ST of 1873, a construction locomotive named Little Bess.

Johnston link-and-pin coupler

The Natal Government Railways (NGR), established in the Colony of Natal in 1875, followed suit and all locomotives and rolling stock acquired by that railway were equipped with Johnston couplers, beginning with the NGR Class K 2-6-0T in 1877.

Likewise, in 1889, when the first locomotives were obtained by the newly established Netherlands-South African Railway Company in the Zuid-Afrikaansche Republiek, they were fitted with Johnston couplers.

Unlike the 2 ft (610 mm) narrow gauge railways of the CGR, those of the NGR also made use of Johnston couplers. The first of these narrow gauge lines came into operation in 1906, when the first NGR Class N 4-6-2T locomotives entered service on the Weenen branch out of Estcourt.

Coupling and uncoupling were done manually, which posed a high risk of serious injury or death to crew members, who had to go between moving vehicles to guide the link into the coupler pocket during coupling. Johnston couplers gradually began to be replaced on the South African Railways from 1927, but not on narrow gauge rolling stock. All new Cape gauge locomotives and rolling stock acquired from that year were equipped with AAR knuckle couplers. Conversion of all older rolling stock was to take several years and both coupler types could still be seen on some vehicles into the late 1950s. During the transition period, knuckle couplers on many locomotives had a horizontal gap and a vertical hole in the knuckle itself to accommodate, respectively, a link and a pin, to enable it to couple to vehicles which were still equipped with the older Johnston couplers.

Bell-and-hook coupler

The bell-and-hook coupling system was first introduced in the Cape of Good Hope in 1902, when two CGR Type A 2-6-4T locomotives were acquired as construction engines on the new 2 ft (610 mm) narrow gauge Avontuur Railway which was being constructed out of Port Elizabeth through the Langkloof. In South Africa, these couplers were used on only the narrow gauge lines in the Cape of Good Hope.

The coupler is similar to the Norwegian coupler. It is a radial coupler with a coupler pocket which is open at the top of the coupling face. Instead of a link and pins, it makes use of a drawhook which, upon coupling, slides over the drawhook pin in the coupler of the next vehicle in the train. To prevent the drawhook of the mating coupler from accidental uncoupling, the coupler bell is equipped with a drawhook guard, commonly known as a bridle, above the coupler pocket.

Usual practice was to have a drawhook fitted to only one of the mating couplers and train crews therefore carried spare drawhooks and drawhook pins on the locomotive. While automatic coupling is possible, this rarely happens and manual assistance is required during coupling. Uncoupling is done manually by lifting the drawhook by hand to release it. The coupler could be adapted to be compatible with the Johnston coupler by replacing the drawhook with a U-shaped adapter link, which was attached using the same drawhook pin.

Bell-and-hook couplers began to be replaced on the Avontuur Railway upon the introduction of Class 91-000 diesel-electric locomotives on the narrow gauge system in 1973. All new narrow gauge rolling stock acquired for that line from that year were equipped with Willison couplers. Older rolling stock were not converted and an adapter was used to enable coupling between the two types. The drawhook on the bell-and-hook coupler would be replaced with the adapter, which was attached using the same drawhook pin.

• 
  Bell-and-hook coupler
• 
  Bell-and-hook coupler with Willison adapter
• 
  Willison coupler adapter for bell-and-hook couplers
• 
  Bell-and-hook coupler with Johnston coupler adapter link instead of a hook

Automatic couplers

There are a number of automatic train couplings, most of which are mutually incompatible. The level of automation varies and can be divided into categories:

• mechanical coupling of vehicles only, requires manual connection of pneumatic and electrical lines;
• mechanical coupling of vehicles with automatic connection of pneumatic lines, requires manual connection of electrical lines;
• mechanical coupling of vehicles with automatic connection of pneumatic and electrical lines (but not data transmission lines);
• mechanical coupling of vehicles with automatic connection of pneumatic and electrical lines (including data transmission lines);
• mechanical coupling of vehicles with automatic connection of pneumatic and electrical lines (including data transmission lines) and automatic uncoupling capability.

Buckeye/Janney/MCB/ARA/AAR/APTA couplers

Main articles: Janney coupler and Tightlock coupling

Syracuse Malleable Iron Works – 1894. The gap in the knuckle accommodates the link of a link and pin coupler and the vertical hole in the knuckle accommodates the pin. This design was used in the transition period.

Knuckle (AAR Type "E") couplers in use

Diagram of the top view of Janney's coupler design as published in his patent application in 1873

APT Type H Tightlock coupler on British Rail Class 321.
Lower electric connector is not typical in North America.

The Janney coupler, later the Master Car Builders Association (MCB) coupler, now the Association of American Railroads (AAR) coupler, is also commonly known as a buckeye, knuckle, or Alliance coupler. The AAR/APTA TypeE, TypeF, and TypeH couplers are all compatible Janney couplers, but used for different rail cars (general freight, tank cars, rotary hoppers, passenger, etc.).

The knuckle coupler or Janney coupler was invented by Eli H. Janney, who received a patent in 1873 (U.S. patent 138,405). It is also known as a buckeye coupler, notably in the United Kingdom, where some rolling stock (mostly for passenger trains) is fitted with it. Janney was a dry goods clerk and former Confederate Army officer from Alexandria, Virginia, who used his lunch hours to whittle from wood an alternative to the link and pin coupler. The term buckeye comes from the nickname of the US state of Ohio, the "Buckeye State" and the Ohio Brass Company which originally marketed the coupling.

In 1893, satisfied that an automatic coupler could meet the demands of commercial railroad operations and, at the same time, be manipulated safely, the United States Congress passed the Safety Appliance Act. Its success in promoting switchyard safety was stunning. Between 1877 and 1887, approximately 38% of all railworker accidents involved coupling. That percentage fell as the railroads began to replace link and pin couplers with automatic couplers. By 1902, only two years after the SAA's effective date, coupling accidents constituted only 4% of all employee accidents. Coupler-related accidents dropped from nearly 11,000 in 1892 to just over 2,000 in 1902, even though the number of railroad employees steadily increased during that decade.

When the Janney coupler was chosen to be the North American standard, there were 8,000 patented alternatives to choose from. Many AAR coupler designs exist to accommodate requirements of various car designs, but all are required to have certain dimensions in common which allow for one design to couple to any other.

The Janney coupler is used in the United States, Canada, Mexico, Japan, India, Taiwan, Australia, New Zealand, South Africa, Saudi Arabia, Cuba, Chile, Brazil, Portugal, China and many countries in Africa both standard gauge and narrow gauges.

The Janney coupler generally provides only mechanical coupling, only Type H adds automatic connections of pneumatic and electrical lines.

Changes since 1873

Main article: Janney coupler § Changes since 1873

Bazeley coupler

Main article: Janney coupler § Bazeley coupler

Henricot coupler

Main article: Janney coupler § Henricot coupler

The Henricot coupler is a variation on the Janney coupler, introduced by Belgian engineer and entrepreneur Émile Henricot of Court-Saint-Étienne. It is used on certain EMUs of the National Railway Company of Belgium, including the Class 75).

• Henricot couplers
• 
  Henricot coupler on an SNCB Class 75 EMU with separate air brake and head-end power connections
• 
  Henricot coupler on a Belgian EMU
• 
  Closeup of Henricot coupler

Willison/SA3 coupler

Main article: SA3 coupler

The simplified scheme of the SA-3 automatic couplers.
An animation of the SA-3 coupler

Willison coupler on South African 2 ft (610 mm) narrow gauge

The Willison coupler was developed in the US in 1916 to address issues present in the Janney coupling.

The Russian SA3 coupler works according to the same principles as the AAR coupler but the two types are incompatible. It was introduced in the Soviet Union in 1932 based on a British patent and has since been used on the whole 1,520 mm (4 ft 11+27⁄32 in) network, including Mongolia. Finnish locomotives have Unilink couplers that can couple to UIC couplers used in Finnish stock and SA3 couplers used in Russian stock.

It is also used on the 1,435 mm (4 ft 8+1⁄2 in) standard gauge networks of Iran and on Malmbanan in Sweden for ore trains. Some 2 ft (610 mm) gauge cane tramway vehicles in Queensland have been fitted with miniature Willison couplers. It was introduced on the 2 ft (610 mm) narrow gauge Avontuur Railway of the South African Railways in 1973.

• Russian trains are rarely longer than about 750 m (2,461 ft) and rarely exceed a maximum tonnage of about 6,000 t (5,900 long tons; 6,600 short tons). The heaviest trains using these couplers are on Malmbanan where they are up to 9,000 t (8,900 long tons; 9,900 short tons).
• Maximum force the SA3 coupler is able to carry, both tensile and compressive, is about 2.5 MN (280 STf; 250 LTf).
• The maximum allowed tractive effort to the SA-3 is limited to 135 tf (1,320 kN; 133 LTf; 149 STf) (1.32 MN or 300,000 lbf) by Russian white papers.
• The proposed European automatic coupler is compatible with the Russian coupler but with automatic air, control and power connections. Implementation is permanently delayed except for a few users. See Europe below.
• The SA3 resembles a left-handed fist.

The SA3 coupler is one of the strongest couplers in the world – maximum tonnage of a train that uses this type of coupler is about 8000 t – but provides only mechanical coupling. Adding automatic electrical and pneumatic connectivity is a complex challenge.

There are many variations and brand names for these couplers.

As of 2020 CAF is working on an automatic coupler based on SA3, a possible replacement of the buffers and chain coupling on European railways.

Unicoupler/Intermat

Intermat and Unicoupler heads from above

Unicoupler has been developed by Knorr from West Germany in the 1970s, in parallel with a compatible counterpart, the Intermat coupler, by VEB Waggonbau Bautzen from East Germany. The Unicoupler/Intermat coupler can automatically couple two pneumatic lines and up to six electrical connections.

This coupler is mechanically compatible with SA-3 and Willison couplers (but pneumatic and electrical connections must be done manually). The Unicoupler is also known as AK69e.

Maximum tonnage of a train that uses this type of coupler is about 6000 t. AK69e and Intermat adoption failure has been attributed to economic performance.

As of 2020 it has found limited use, it's been adopted by the Iranian Railways and is also used in Germany on trains transporting iron ore between Hamburg and Salzgitter.

C-AKv

Main article: C-AKv coupler

The C-AKv coupler (also called Transpact) is a newer compact Willison coupler developed by Faiveley Transport. It is mechanically compatible with the SA3 coupler (but pneumatic and electrical connections must be done manually), fully compatible with the Unicoupler and, if additional buffers are mounted, it can be coupled with the conventional European screw coupling as well. The C-AKv coupler can automatically couple two pneumatic lines. As of 2020 its use is limited to trains transporting ore between Rotterdam and Dillingen steelworks and lignite between Wählitz and Buna in Germany.

Z-AK

The Z-AK coupler is yet another Willison coupler developed by Knorr Bremse. It was designed in response to the obvious failure of the Unicoupler/Intermat. It is compatible with the buffers and screw coupling. It is one of only few automatic couplers that cannot carry tensile forces, railway vehicles using this type of coupler must be equipped with buffers as well.

Unilink coupler

The Unilink coupler is a coupler, which is used in CSI border countries such as Finland or Ukraine. The coupler is compatible with both SA3 and screw coupling. It is an SA3 coupler with an additional horn that allows to attach the shackle of the screw coupler and with a screw coupler that is connected to the hook of wagons equipped with screw couplers. When the screw coupler is not in use, the coupler shakle rests in a holder on the left side of the coupler. Rolling stock equipped with Unilink couplers is also equipped with side buffers, which are required when using the screw coupler.

Finland uses passenger coaches equipped with screw couplers because they have the advantage over the SA3 coupler of providing a slack-free ride, as the screw couplers are always under tension and the side buffers do not separate in normal operation. Most Finish freight cars are also equipped with screw couplers. Only some heavy freight cars and Russian equipment are fitted with SA3 couplers.

Automatic Buffing Contact Coupler (ABC Coupler)

ABC coupler on a Kalka–Shimla train

The Automatic Buffing Contact Coupler, better known as the ABC coupler, was invented by J.T. Jepson, patented in Great Britain in 1906 and manufactured by the A.B.C. Coupler and Engineering Company Limited in a factory in Wolverhampton.

The coupling consists of a shackle that protrudes from a central buffer and falls into a hook in the opposite buffer when coupling contact is made. The non-engaged shackle of the opposite coupler rests on the engaged shackle, securing it against disengagement by its weight. To uncouple the ABC coupling, the upper shackle that is not engaged is lifted. This causes the tail lever attached to the shackle to lift the engaged shackle clear of the hook and release the coupling.

In 1912, an improved version of the coupling with a better locking mechanism was introduced, in which a spring-loaded locking bar blocked a disk serving as the hook. This disc hook was rotated into the locked position by the approaching shackle of the opposite coupling. To release the coupling, it was sufficient to release the locking bar by pulling on a chain or a handle, which released the rotation of the disk hook.

The coupler was mainly used on narrow gauge railways of the British colonies, like e.g. the Bauchi Light Railway in Nigeria, Ceylon, Honduras or the Kalka-Shimla Railway in India.

Stearns and Ward coupler

Stearns and Wards coupler on a car of the Northwestern Elevated Railroad

The Stearns and Ward coupler, known as the Ward coupler in the United Kingdom, is named after its two American inventors, Robert B. Stearns and Frank D. Ward, who were jointly granted the patent US 737673  "Car-coupling." in 1903. The coupler was specifically designed for use on elevated railways as they were introduced in Chicago at the turn of the century. It was first used on the electric trains of the Northwestern Elevated Railroad in 1902. Three years later in 1905 it was introduced by Wards in the electrification of the Circle Line of the District Railway, which became the London Underground. The Ward coupler was the standard coupler on London Underground trains until 1936, when it was replaced by the Wedglock coupler, a multi-function coupler that also provided pneumatic and electrical connections.

The cars must be pushed together to couple. The tongue of each coupler head enters the throat of the opposite coupler head, where the hook on the tongue turns a vertically mounted, spring-loaded coupling pin against the force of the spring. Once the hook passes the coupling pin, the spring force returns the coupling pin to its original position, holding the hook head in the coupling. When coupled, the coupler heads are free to move vertically, which should prevent a derailed car from dragging other cars with it in the event of a derailment on the elevated railway. Uncoupling is done by turning the coupling pin against the spring force with an actuating arm operated by a shunting pole or by a fixed rod with handles that can be reached from a position next to the train away from the third rail.

Multi-function couplers

Multi-function couplers (MFCs), or fully automatic couplers, make all connections between the rail vehicles (mechanical, air brake, and electrical) without human intervention, in contrast to autocouplers, or semi-automatic couplers, which just handle the mechanical aspects. The majority of trains fitted with these types of couplers are multiple units, especially those used in mass transit operations.

There are a few designs of fully automatic couplers in use worldwide, including the Scharfenberg coupler, various knuckle hybrids such as the Tightlock (used in the UK), the Wedglock coupling, Dellner couplings (similar to Scharfenberg couplers in appearance), BSI coupling (Bergische Stahl Industrie, now Faiveley Transport) and the Schaku-Tomlinson Tightlock coupling.

There are a number of other automatic train couplings similar to the Scharfenberg coupler, but not necessarily compatible with it. Older US transit operators continue to use these non-Janney electro-pneumatic coupler designs and have used them for decades.

Westinghouse H2C

The Westinghouse H2C coupler, whose predecessor the H2A was first used on the BMT Standards and later the R1 through R9 classes, is currently used on the R32, R42, R62, R62A, R68, and R68A class subway cars of the New York City Subway. The A ends of the cars typically have the Westinghouse coupler and the B ends use either a semi-permanent drawbar, or a Westinghouse coupler.

WABCO N-Type

WABCO Model N-2 on a SEPTA Silverliner II

The WABCO N-Type coupler was first developed for the prototype Pittsburgh Skybus system with the initial model N-1 as applied only to the three Skybus cars. The updated model N-2 with a larger 4-inch (101.6 mm) gathering range was first applied to the new "Airporter" rapid transit cars on the Cleveland Rapid Transit line. The model N-2 used lightweight draft gear slung below the center sill, to allow for the wide swings required to go around sharp curves. This made the N-2 unsuitable for main line railroad use so an updated version N-2-A was developed for that market. The first of these were fitted in 1968 to the UAC TurboTrain with 228 electrical contacts and the Budd Metropolitan EMU with 138 contacts. Starting in the 1970s the N-2-A was fitted to the entire SEPTA Silverliner family of MU's, the NJT Arrow series of MU's and the Metro-North Railroad/Long Island Rail Road M series of MU railcars. The N-2 was also used by the PATCO Speedline, but was replaced due to issues with the electrical contacts. Later WABCO would create a new model N-3 for the BART system with a 6-by-4-inch (152.4 mm × 101.6 mm) gathering range which required a rectangular funnel.

The WABCO N-type is sometimes referred to as the pin and cup coupler or spear coupler.

Tomlinson

Tomlinson coupler as applied to a New York City Subway R46

Tomlinson coupler as used on Eidan Subway (now Tokyo Metro) 300 series

The Tomlinson coupler was developed by the Ohio Brass Company for mass transit applications, but eventually found use in some mainline railroad vehicles as well. It consists of two squared metal hooks that engage with each other in a larger rectangular frame with air line connections above and below. Since the coupler's development the manufacturing arm of Ohio Brass was purchased by WABCO which now manufacturers the line along with the N-type. The Tomlinson coupler is the most widely used fully automatic heavy rail coupling in North America having been adopted by the Washington Metro, Massachusetts Bay Transportation Authority, PATCO Speedline, SEPTA Broad Street Subway, Los Angeles Metro Rail, Baltimore Metro, Miami Metro, MARTA Rail and the New York City Subway for its R44/R46 fleet and all modern classes starting with the R142. For applications outside of rapid transit the coupler had to be significantly enlarged to meet the increased strength requirements first appearing in this capacity on the Budd Metroliner and later on the Illinois Central Highliner fleet. Its relative lack of strength is one reason the N-Type has been more successful in the mainline railroad arena.

Outside the United States, the Tomlinson coupler is used on Tokyo Metro's Ginza and Marunouchi Lines and on the heavy capacity Taipei Metro lines.

Scharfenberg coupler

Main article: Scharfenberg coupler

Scharfenberg coupler

Scharfenberg coupler
made by Dellner

The Scharfenberg coupler (German: Scharfenbergkupplung or Schaku) is probably the most commonly used type of fully automatic coupling. Designed in 1903 by Karl Scharfenberg in Königsberg, Germany (today Kaliningrad, Russia), it has gradually spread from transit trains to regular passenger service trains, although outside Europe its use is generally restricted to mass transit systems. The Schaku coupler is superior in many ways to many other automatic couplers because it makes the pneumatic and electrical connections automatically and is capable of automatic uncoupling. However, there is no standard for the placement of these electro-pneumatic connections. Some rail companies have them placed on the sides while others have them placed above the mechanical portion of the Schaku coupler.

Small air cylinders, acting on the rotating heads of the coupler, ensure the Schaku coupler engagement, making it unnecessary to use shock to get a good coupling. Joining portions of a passenger train can be done at very low speed (less than 2 mph or 3.2 km/h in the final approach), so that the passengers are not jostled about. Rail equipment manufacturers such as Bombardier offer the Schaku coupler as an option on their mass transit systems and their passenger cars and locomotives. In North America all the trains of the Montreal Metro are equipped with it, as are new light rail systems in Denver, Baltimore and New Jersey. It is also used on light rail vehicles in Portland, Minneapolis, the Vancouver Skytrain, and Line 3 Scarborough in Toronto. In New Zealand, it is found on the electric AM class of Auckland's suburban rail network, and on the Matangi trains of Wellington's. It also equips all the dedicated rolling stock used for the shuttle services in the Channel Tunnel.

Maximum tonnage under 1,000 t (1,100 short tons; 980 long tons).

As of 2020 Voith and Dellner are working on an automatic coupler based on Schaku, a possible replacement of the buffers and chain coupling on European railways.

Dellner coupler

Main article: Dellner

Dellner coupler on a Virgin CrossCountry Class 221 at Carlisle on 10 October 2005

The Swedish-made Dellner coupling, is a proprietary version of the Scharfenberg coupler, connecting vehicle, pneumatics and electronics at the same time. The patented energy absorption D-BOX technology allows coupling at speeds of up to 15 kilometres per hour (9 mph) with no structural damage, and up to 36 kilometres per hour (22 mph) with deformation but with the vehicles remaining on track. The patented D-REX system provides Ethernet high speed data connection at speeds of 100 Mbit/s.

Wedglock coupler

Wedglock coupler on a London Underground train

The Wedglock coupler is named for the pneumatic wedges that lock the moving parts of the coupler head in the engaged position. It is the standard automatic coupler used on London Underground trains. The coupler was introduced in 1936 and is manufactured by William Cook Rail. and Voith. The face of the coupler has a protruding, movable tongue which is inserted into the throat of the opposite coupler during coupling. Once these mechanical elements are fully engaged, their position is locked by wedges driven by a pneumatic cylinder. The pneumatic pots are located below the mechanical connection. They are simply pressed together and sealed by rubber elements. On either side of the mechanical connection are electrical contact blocks consisting of a series of butt contacts. When disconnected, the contacts are protected by the so called "Dutch oven" covers. The covers are mechanically actuated and swing open when the other coupling approaches. The coupling can be engaged and disengaged from the cab using the three-position coupling switch in the cab.

GF Coupler

GFN coupler on an EMU of the Appenzell Railways

GFV coupler produced by the Schwab Verkehrstechnik AG

The GF coupler, sometimes also written as +GF+ coupler, is a coupler manufacturend by Georg Fischer in Schaffhausen, Switzerland and was widely used on Swiss railways and on vehicles produced by the Swiss railway industry. It was first shown at the Swiss National Exhibition in Bern in 1914. There were three variants available, the GFN type for interurban railways, the GFT type for trams and the GFV type for mass transit.

GFN and GFT

The GFN and GFT types are very similar. The only difference is that the GFT is designed for lower forces as expected in tram service. Both couplings consist of a rectangular buffer that doubles as a throat. A horizontal tongue with a hole protrudes from the inside of the throat into which the verticaly arranged locking pin hooks. To uncouple, the locking pin can be lifted with handles located behind the coupler. Optionally, the air and electrical lines can also be connected. Air connections are typically located above and/or below the mechanical coupling. The electrical contacts are located above the coupler and are protected from contamination by a hinged cover when uncoupled.

The first railways introducing the GFN type coupler where the Bern-Zollikofen-Bahn, now part of the Regionalverkehr Bern-Solothurn, the Aarau–Schöftland-Bahn, now part of the Wynental and Suhrental Railway, and the Biel–Täuffelen–Ins railway. An other important railway using the GFN type coupler is the Brünig railway. The lighter GFT type coupler was first used by the Strassenbahn Zürich–Oerlikon–Seebach and was later introduced to almost all tram services in Switzerland.

GFV

The GFV differs significantly from the GFN and GFT. It is typically designed as a fully automatic multi-function coupler that can be disengaged at the push of a button in the cab. The design is more similar to a Schafrenberg coupler. The mechanical connection is made by a hemispherical element protruding from the coupling head, which is inserted and locked into a half-shell-shaped pocket on the opposite coupling head. The two air connections are located one above the other below the mechanical coupling next to the guide horn, and the electrical connections are located above the coupling as with the GFN and GFV types. The type was first introduced 1965 with the so called Gold Coast Express used as the first mass transit trains in the Greater Zurich area. It is still widely used on Zürich S-Bahn equipment and in Belgium by the SNCB.

Schwab coupler

Schwab coupler FK-15-10 on a Stadler FLIRT of the Swiss Federal Railways (SBB)

The Schwab coupler is an automatic coupler manufactured by Schwab Verkehrstechnik AG, Schaffhausen, the legal successor to the Railway Coupler Division of Georg Fischer. The coupler automatically makes the mechanical, pneumatic and electrical connections. The mechanical locks are located on either side of the pneumatic ports. The electrical connections are located below the pneumatic ports and are protected by a cover when disconnected. Several versions are available for different applications, which can only be coupled to each other and not to other couplings, except the FK-15-10 version which can be coupled to the Scharfenberg coupling type 10. A special feature of the Schwab coupler is the inclined coupler face, which causes the coupler heads to slide past each other during coupling, so that snow and ice are scraped off the coupler faces in winter.

As of 2020 Schwab couplers are used primarily in Switzerland in regional rail passenger transport. Almost all vehicles fitted with Schwab couplers are manufactured by Stadler Rail. The best known exception are the ICN tilt trains operated by Swiss Federal Railways (SBB).

The following versions exist:

• standard gauge mainline railroads:
  • FK-15-12, which are used on Stadler KISS, Stadler GTW and Stadler FLIRT
  • FK-15-10, which is compatible with the Scharfenberg type 10 coupler
• metros and suburban railways: FK-9-6
• streetcars and narrow gauge railcars: FK-5.5-4 and FK-3-2.5

As of 2020 Wabtec is working on an Digital automatic coupling (DAC) based the Schwab coupler, a possible replacement of the screw couplers in the European rail freight service. The coupler is able to handle tensile forces up to 1500 kN and compressive forces up to 2000 kN and is therefore one of the strongest couplers ever designed for European railways.

Shibata coupler

The Shibata coupler is a variation of the Scharfenberg coupler which was developed by Japanese Government Railways (JGR) engineer Mamoru Shibata in the 1930s for electric trains. It is the standard coupler type for all passenger trains in Japan as well as on commuter and subway trains in South Korea.

Shinkansen (bullet train) rolling stock utilize a variation of the Shibata coupler developed by Sumitomo Metal Industries in the 1960s which uses rotary tight-lock pins, and which coincidentally bears a closer resemblance to the Scharfenberg coupler rather than the Shibata coupler.

• Shibata couplers
• 
  Shibata close contact ("Mitchaku") coupler
• 
  Shibata rotary coupler on E4 Series Shinkansen

Dual couplings and match wagons

Main articles: Dual coupling and barrier vehicle

Coupling adapter for use between Janney coupler on a locomotive and WABCO N-2 couplers fitted to commuter rail multiple units at New York's Pennsylvania Station. The adapter is seen from the bottom.

Transition era AAR knuckle coupler. The gap in the knuckle accommodates the link of a Johnston coupler or a link and pin coupler and the vertical hole in the knuckle accommodates the pin.

Sometimes a wagon with one coupling system needs to be coupled to wagons with another coupling type This may be needed when taking metro rolling stock from its manufacturer to the city where it is to be used. There are two solutions:

• use a barrier vehicle(s) which has different couplings at either end.
• use a coupling adaptor.
• use a match wagon which has the same dual coupling at both ends.

Only some kinds of couplings coexist on the end of a wagon at the same time, because amongst other reasons they need to be at the same height. For example, in the Australian state of Victoria, engines had the AAR coupler, with buffers, and the chain mounted on a lug cast into the AAR coupler.

A barrier vehicle / wagon in Britain and "transition car" in North America) has different kinds of couplings at each end. If a pair of barrier vehicles is used, a rake of wagons using coupling A can be inserted into a train otherwise using coupling B.

A coupling adaptor or compromise coupler might couple to an AAR coupling on a wagon, and present, for example, a meatchopper coupler or rapid transit coupler to the next wagon. Such an adaptor might weigh 100 kg (220 lb). An adapter piece allows a Janney coupler mate with an SA3 coupler.

Dual coupling

Main article: Dual coupling

Sets of carriages

Further information: Dual coupling

Automatic couplers like the Janney are safer in a collision because they help prevent the carriages telescoping. British Rail therefore decided to adopt a Janney variant for its passenger carriages, with the coupler able to swing out of the way for coupling to engines with the traditional buffer and chain system.

In New South Wales, sets of carriages were permanently coupled with a fixed bar, since the carriages were disconnected only at the workshops. Freight cars are sometimes coupled in pairs or triplets, using bar couplings in between.

Articulated sets of carriages or wagons share the intermediate bogies, and have no need for couplings in the intermediate positions.

Brake couplings

Main article: Railway brake

Couplings are needed for any continuous braking systems.

Electronically controlled brakes

Electronically controlled pneumatic brakes (ECP) need a method of connecting electrically adjacent wagons, both for power and for command signals, and this can be done by plugs and sockets, or by very short range radio signals.

Draw gear

A draw gear (also known as a draft gear) is the assembly behind the coupling at each end of the wagon to take care of the compression and tension forces between the wagons of trains. Early draw gears were made of wood, which was gradually replaced by steel.

Janney couplers have the draft gear in a centersill to absorb the pushing and pulling forces (slack action).

There is also a draw gear behind tightlock couplers, SA3 couplers, C-AKv couplers, Scharfenberg couplers, and other multi-function couplers.

In the case of buffers and chain couplers, the draw gear behind the hooks, if any, will absorb the tension, while the side buffers will absorb the compression.

Some couplers may not have a draw gear.

Model railway couplers

Main article: Rail transport modelling

On model railroads couplers vary according to scale, and have evolved over many years. Early model trains were coupled using various hook-and-loop arrangements, which were frequently asymmetrical, requiring all cars to be pointing in the same direction. In the larger scales, working scale or near-scale models of Janney couplers were quite common, but proved impractical in HO and smaller scales.

For many years, the "X2F" or "Horn-Hook" coupler was quite common in HO scale, as it could be produced as a single piece of moulded plastic. Similarly, for many years, a "lift-hook" coupler known as the Rapido and developed by Arnold, a German manufacturer of N-scale model trains, was commonly used in that scale.

The chief competitor of both these couplers, more popular among serious modellers, was the Magne-Matic, a magnetically released knuckle coupler developed by Keith and Dale Edwards, and manufactured by Kadee, a company they started. While they closely resemble miniature Janney couplers, they are somewhat different mechanically, with the knuckle pivoting from the center of the coupler head, rather than from the side. A steel pin, designed to resemble an air brake hose, allows the couplers to be released magnetically; the design of the coupler head prevents this from happening unless the train is stopped or reversed with a mated pair of couplers directly over an uncoupling magnet. An earlier, mechanically tripped version of the design had a straight pin extending down from the knuckle itself, which engaged a diamond-shaped mechanical "ramp" between the rails, which had to be raised above rail height when uncoupling was desired.

Once the Kadee patents ran out, a number of other manufacturers began to manufacture similar (and compatible) magnetic knuckle couplers.

An exact-scale HO model of the AAR coupler has been designed and manufactured by Frank Sergent. This design uses a tiny stainless steel ball to lock the knuckle closed. Uncoupling is achieved by holding a magnetic wand over the coupler pair to draw the balls out of the locking pockets.

In O scale, an exact-scale working miniature version of the "Alliance" coupler was manufactured from the 1980s by GAGO models in Australia. Since 2002 it has been marketed by the Waratah Model Railway Company. European modellers tend to use scale hook and chain couplings.

In British 00 scale (similar to H0 scale) models the 'tension lock' coupler developed by Tri-ang is standard. This is similar in operation to the meatchopper type of coupling. Remote uncoupling is possible by using a sprung ramp between the rails. The design of the hooks is such that the couplings will not uncouple when under tension (instead depressing the ramp). When the train is pushed over the ramp, it will lift the coupling hooks as the train passes over. By halting the train over the ramp, it is split at this point. While it works well, it is often seen as ugly and obtrusive (although smaller designs are available, these are not always fully compatible with other models) and many British modellers prefer to retrofit either Kadee types or working hook and chain couplings.

A recent development is an interchangeable coupling which plugs into a standardised socket, known as NEM 362 and which can be easily unplugged as required. This allows the modeller to easily standardise on whatever coupling is desired, without individual manufacturers needing to change their coupling type.

In 7 mm scale, scale working Norwegian couplings are now being manufactured by Zamzoodled in the UK.

A comparison of coupler types was published in "An introduction to Couplers".

Wooden and plastic trains

Toy trains have a wide variety of incompatible couplers.

Accidents

Different kinds of coupling have different accident rates.

• The Murulla rail accident of 1926 involved the breakage of a "drawhook" leading to a downhill runaway and then a collision. Drawhooks imply "buffers and chain couplers".
• Round Oak rail accident – 1858 – coupling broke and the rear of train rolled back.

See also

• Buckeye Steel Castings
• Drawbar
• Gangway connection
• Gender of connectors and fasteners
• Jane's World Railways, lists the coupler(s) used on any railway system
• Railway coupling by country
• Railway coupling conversion
• Slack action
• Three-point hitch

References

Sources

• Tymczasowe wytyczne obsługi sprzęgu samoczynnego typu UIC/OSŻD, radzieckiego – typu SA3 oraz sprzęgu mieszanego [Interim guidelines for operation of automatic coupler type UIC/OSJD, Soviet—SA3 and adapter] (in Polish). Warsaw: Ministerstwo Komunikacji. 1979.
• Development of Functional Requirements for Sustainable and Attractive European Rail Freight: D5.1 – State of the Art on Automatic Couplers (PDF) (Technical report). Shift2Rail. 3 March 2017.
• Prof. Dr. Markus Hecht, Markus; Mirko Leiste, M.Sc.; Saskia Discher, B.Sc., eds. (29 June 2020). Development of a concept for the EU-wide migration to a digital automatic coupling system (DAC) for rail freight transportation (PDF) (Technical report). Berlin: Berlin University of Technology for the Federal Ministry of Transport and Digital Infrastructure (BMVI).
• Norfolk & Western Railway Co. v. Hiles (95-6), 516 U.S. 400 (1996) (U.S. Supreme Court decision by Justice Clarence Thomas)
• Eli Janney — The Janney Coupler Archived 2008-11-06 at the Library of Congress Web Archives (based on above case)
• Dellner Couplers AB — Automatic and Semi-Permanent Couplers
• Vancouver SkyTrain Light Rail Network, Canada (these two for Dellner data)
• JANE'S WORLD RAILWAYS
• How couplings work
• White, John H. (1985) [1978]. The American Railroad Passenger Car. Baltimore, Maryland: Johns Hopkins University Press. ISBN 978-0-8018-2743-3.

Further reading

Tomlinson, G. W. (1991). "Electrical Systems via Couplers". Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit. 205 (1): 65–78. doi:10.1243/PIME_PROC_1991_205_217_02. S2CID 111315979.

External links

• US patent 4102459, Axel Schelle & Kuno Nell, "Adaptor device for coupling railway vehicles having different types of couplers", published 1978-07-25 , Adapter between Janney coupler and SA3 coupler